[00:00] Detailing 101, I'm Ivan, this is DIY Detail. Today we're going to be talking about Incredible Suds.
[00:12] Incredible Suds is our soap and a great wash soap. First of all, the dilution ratio. Incredible Suds is very thick and very concentrated formula. In a foam cannon, you're going to put 31 ounces of
[00:27] water and two capfuls or one ounce of Incredible Suds is all you need. There's one and there's
[00:42] the second. Now if you want thicker foam, yes you can add a little more, but for cleaning ability that's all you need. In your bucket all you need is one cap full. One cap full of
[00:56] incredible suds, just clean out the cap, put it back on the bottle. Once that's back on the bottle I can use my foam cannon and one very important point with
[01:16] your foam can. You have to mix it up. If you notice, I'll flip it over here and we still have the incredible suds on the bottom. You need to mix it up because it is a very thick formula, so we want to make sure that it's well distributed. If
[01:31] you're getting poor foam out of it, it could be that you just didn't mix it up properly. In the bucket itself, we have a few different ways of getting foam. One,
[01:45] you could stir it by hand, but if you have a pressure washer or hose, this works exceptionally well. As you can see we have very thick lather ready to wash the vehicle. You can use
[02:10] different types of wash media. One is the traditional wash mitt and the other is our Legacy Sponge. Both do a great job. The Legacy Sponge is my preferred because you have less
[02:23] chance of pressure points on the vehicle, therefore a better wash and a safer wash. Now, before washing a vehicle, you need to pre-treat it. A couple different ways of doing so.
[02:38] One is with your pressure washer, adding water. The pressure washer on a dirty vehicle, you're actually taking pressure and pushing the dirt across the surface. So not the safest way
[02:50] of doing it. If you don't have a pressure washer you can get a foamer like this. Now in here we have the same dilution as we have in the bucket and this is the foam that you get. So a very nice
[03:08] thick foam. But as detailers we like to play with power tools, therefore the pressure washer. When you're using a pressure washer always assure yourself
[03:28] that the tip is in and here we go. And if you want a thicker foam like I said just add a little more Incredible Suds Next we actually letting the soap dwell on the surface And instead of doing a two bucket wash like a lot of people do because at this point some people would take that take their
[04:02] wash media, and start washing. Unfortunately, if there's any grit on the car, they're also going to be driving the grit into the paint. Even though it's lubricated and safe, it's still a possibility.
[04:14] Instead of using two buckets, I like to do a two-foam method, which means we put the foam on the surface, let it emulsify the dirt, let it break it down, then we take our pressure washer and rinse it very quickly.
[04:28] There's no need for a full rinse.
[04:46] We're just taking the dirt that could be on the surface and removing it. Next we'll foam again with the pressure washer.
[04:59] And then we can do our contact wash. Like I said, we could use a wash mitt like this to do our contact wash. You want to be sure you work from the top to the bottom and not come back up.
[05:13] Next, be very methodical. You want to make sure that you're getting the contact everywhere. Using the Legacy Sponge, again, no pressure, going from top to bottom.
[05:31] Once you're done a panel, you can flip the sponge, do the next panel. Once you've done that, dunk it back in your wash.
[05:44] Get it ready to go the next one From there we rinse and we dry When you using a pressure washer always make sure that when you insert the tip and it well locked and aim at
[05:57] the floor first just in case. Finally, when washing with Incredible Suds or any wash soap, you don't want to dry once
[06:20] you've rinsed off. You need some form of drying aid. In this case, I'll be using Quick Beads, which is our water-activated drying aid and sealant. You see it automatically, as you can see it instantly starts working and it will provide
[06:36] the lubrication we need when drying. Because water is not a lubricant, water is a solvent and unfortunately can damage the paint if you're drying. Therefore, once we have the Quick Beads on, it's a spray on, rinse off product.
[07:02] Now drying will be not only safer, but easier. pass and the panel is dry. If you have any questions, comments, thoughts, or ideas,
[07:18] please leave them below and we'll see you in the next Detailing 101.
[07:43] you